Flash Dropped in the Sea: How to Save Wet Camera Gear

Now and then camera gear takes an unplanned dip, and it gets far worse when the water is salty, like the sea we all love so much. Here is the story of my own equipment's first swim, plus what to do when your gear ends up in the water.

Flash and Pocket Wizard radio trigger soaking in glass jars of water

Overview

Key facts

  • During a shoot, a Nikon SB-800 flash and a Pocket Wizard radio trigger toppled into the sea; this post tells the story and explains how to save electronics that got wet.
  • Wind and waves tipped the gear over, and it stayed underwater for roughly 15 seconds.
  • Take the batteries out straight away; if the water was salty, rinse the device in distilled water without delay.
  • The suggested routine is to soak it and swap the distilled water roughly 3 times over no less than 3-5 days, followed by several days of careful drying.
  • The SB-800 came through and worked flawlessly, whereas the Pocket Wizards could no longer transmit or receive a radio signal.

What Happened

Model in a purple tutu standing in the sea beside a light stand with a flashThe previous day I had a lovely shoot by the sea. Because the wind was strong, I had taken the umbrella and every other modifier off the flash, since anything that catches the wind could tip the light into the water. Then, out of nowhere, a much stronger gust came, and the waves toppled the stand carrying the Nikon SB-800, which was switched on, together with its Pocket Wizard radio trigger. The two units spent only about 15 seconds underwater, yet that was more than enough to drown them. I dashed over and fished everything out as fast as I could.

How to Rescue Wet Electronics

Nikon SB-800 flash and Pocket Wizard Plus II being rinsed in glass jarsWhenever this happens, start by taking out the batteries or disconnecting any other power source. Gear that has landed in fresh water only needs drying, after which you keep your fingers crossed that it still works; salt water causes far bigger trouble. Salt reacts with metal, and some electronic parts even begin to corrode, so the first job is a rinse in distilled water, and the sooner you do it, the better. Distilled water is sold for cars, which means any Statoil petrol station and plenty of other shops stock it. Your first goal, then, is to wash every trace of salt out of the gear, ideally after taking the device apart.Bottle of distilled water used to rinse salt out of the flash Leave it submerged in distilled water for a few hours. Next, change to fresh distilled water and leave it for a full day. Go through this rinse roughly 3 times, so the whole routine lasts no less than 3-5 days. After that, open the device up with a screwdriver if you can, blow it out and let it dry completely, which also takes several days. Only once all of this is done should you try switching it on, and only when you are certain it is bone dry. Any other electronics, whether a phone, a camera or something else, deserve the same treatment. Most of the damage comes from rushing: rinsing too briefly and not drying for long enough. Cut the rinse short and, even if the device comes back to life, the salt left inside will gradually eat away at the contacts until it gives up about a month later. Power it up before it is properly dry and it will short-circuit all over again. Good luck with the rinsing and drying!


 

Outcome (Update)

The dip ended in the exact opposite of what I had expected. The Nikon SB-800 flash pulled through and now works flawlessly. The Pocket Wizards, however, are dead: they power up and their lights flash, but they can no longer transmit or receive a radio signal.

 

 

 

Next frame

Keep reading

All stories

Photo Gear Security: Preventing Theft, Fraud and Data Loss

Everyone knows how costly photo gear is. Saving up for a dream camera takes ages, never mind for great lenses. Bought piece by piece, a kit can add up to an impressive sum, and all of it often "fits" into one small camera bag.

Nikon D3 Torture Tests: Food, Hammer and Drop Videos

Out of sheer boredom, an American named Joseph began putting his professional camera gear through durability tests: dropping it from the second floor, soaking it in water, blowing smoke into the camera, a microwave test, using...

Comments 10

  1. rubis#10
    Good photo
  2. FromHell#9
    I heard that drowned equipment can be soaked in alcohol. Its density is low and it drives the water out from all microscopic gaps.
  3. Zaulons#8
    About soaking and drowned gear!

    In general, I have had to repair various things that got into water. Of course salt water is the most tragic.

    I would never agree with the distilled water experiment. Because if it has been salt water, then you cannot wash much out even by changing the water. If you do not have experience and knowledge, then the equipment must urgently be taken to a specialist. But for those who are friends with a screwdriver and a soldering iron, I can tell you what should be done.

    First the device must be completely disassembled into parts, each board separately. If there are solder joints that do not allow it, then they must be unsoldered (that is usually the case with soap dishes).

    After that, the boards should be immersed in petrol (refined petrol sold in construction or similar stores works well). When the board has soaked in petrol for a few minutes, scrub it with a stiff brush (you can use a toothbrush). Repeat this procedure 2-3 times. If after this procedure the device does not work, you can try repeating it, but with drowned gear the result is usually 50/50.
  4. wizulis#7
    How did it go with the equipment in the end? Does it work / not work?
  5. Aleks#6
    It is better, of course, to take it apart, open up the device and then rinse it, then dry it. That is faster and more reliable, because you can see with your own eyes what has oxidized and what has not. I hope the flash will work.
  6. viko#5
    Yeah, everything comes through school : )) next time by the water you need to put a condom on the flash too!
  7. viko#4
    I do not know whether such bathing really does electronics any good...
  8. Martins#3
    Alcohol helps too, but do not drown it, just take it apart and clean it.
  9. Andrejs Zavadskis#2
    unfortunately not
  10. LatFoto#1
    That flash is not water-resistant by any chance, is it? Then maybe such soaking was not especially necessary ;-)?

Leave a comment

Questions, corrections and your own experience are welcome. Your e-mail is never published.

(email will not be published)
Links are not allowed in comments
two plus zero =* (in words)